NAME
encoding::warnings - Warn on implicit encoding conversions
VERSION
This document describes version 0.11 of encoding::warnings, released June 5, 2007.
SYNOPSIS
use encoding::warnings; # or 'FATAL' to raise fatal exceptions
utf8::encode($a = chr(20000)); # a byte-string (raw bytes)
$b = chr(20000); # a unicode-string (wide characters)
# "Bytes implicitly upgraded into wide characters as iso-8859-1"
$c = $a . $b;
DESCRIPTION
Overview of the problem
By default, there is a fundamental asymmetry in Perl's unicode model: implicit upgrading from byte-strings to unicode-strings assumes that they were encoded in ISO 8859-1 (Latin-1), but unicode-strings are downgraded with UTF-8 encoding. This happens because the first 256 codepoints in Unicode happens to agree with Latin-1.
However, this silent upgrading can easily cause problems, if you happen to mix unicode strings with non-Latin1 data -- i.e. byte-strings encoded in UTF-8 or other encodings. The error will not manifest until the combined string is written to output, at which time it would be impossible to see where did the silent upgrading occur.
Detecting the problem
This module simplifies the process of diagnosing such problems. Just put this line on top of your main program:
use encoding::warnings;
Afterwards, implicit upgrading of high-bit bytes will raise a warning. Ex.: Bytes implicitly upgraded into wide characters as iso-8859-1 at - line 7
.
However, strings composed purely of ASCII code points (0x00
..0x7F
) will not trigger this warning.
You can also make the warnings fatal by importing this module as:
use encoding::warnings 'FATAL';
Solving the problem
Most of the time, this warning occurs when a byte-string is concatenated with a unicode-string. There are a number of ways to solve it:
Upgrade both sides to unicode-strings
If your program does not need compatibility for Perl 5.6 and earlier, the recommended approach is to apply appropriate IO disciplines, so all data in your program become unicode-strings. See encoding, open and "binmode" in perlfunc for how.
Downgrade both sides to byte-strings
The other way works too, especially if you are sure that all your data are under the same encoding, or if compatibility with older versions of Perl is desired.
You may downgrade strings with
Encode::encode
andutf8::encode
. See Encode and utf8 for details.Specify the encoding for implicit byte-string upgrading
If you are confident that all byte-strings will be in a specific encoding like UTF-8, and need not support older versions of Perl, use the
encoding
pragma:use encoding 'utf8';
Similarly, this will silence warnings from this module, and preserve the default behaviour:
use encoding 'iso-8859-1';
However, note that
use encoding
actually had three distinct effects:PerlIO layers for STDIN and STDOUT
This is similar to what open pragma does.
Literal conversions
This turns all literal string in your program into unicode-strings (equivalent to a
use utf8
), by decoding them using the specified encoding.Implicit upgrading for byte-strings
This will silence warnings from this module, as shown above.
Because literal conversions also work on empty strings, it may surprise some people:
use encoding 'big5'; my $byte_string = pack("C*", 0xA4, 0x40); print length $a; # 2 here. $a .= ""; # concatenating with a unicode string... print length $a; # 1 here!
In other words, do not
use encoding
unless you are certain that the program will not deal with any raw, 8-bit binary data at all.However, the
Filter => 1
flavor ofuse encoding
will not affect implicit upgrading for byte-strings, and is thus incapable of silencing warnings from this module. See encoding for more details.
CAVEATS
For Perl 5.9.4 or later, this module's effect is lexical.
For Perl versions prior to 5.9.4, this module affects the whole script, instead of inside its lexical block.
SEE ALSO
AUTHORS
Audrey Tang
COPYRIGHT
Copyright 2004, 2005, 2006, 2007 by Audrey Tang <cpan@audreyt.org>.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.